Galaxy S6 Battery Replacement 2021 Step by Step Guide

Galaxy S6 Battery Replacement 2021 Step by Step Guide.

Galaxy S6 – Is your Samsung Galaxy battery dead or not charging? A bad battery can be a very frustrating issue and should be fixed as soon as possible. Check out this step-by-step guild on how to replace your battery yourself.

Galaxy S6 Battery Replacement 2021 Step by Step Guide

Before you begin with the removal of your Samsung Galaxy S6 battery, you should consider a few points in the preparation.

First and foremost, find a workstation that is bright enough and has enough space to remove and install your Galaxy S6 battery. Now you should place everything within reach.

This includes not only your smartphone and tools but also a hairdryer. You need this to open the case later.

Place a small bowl ready for you, where you can store items such as screws during removal and installation to help you through your Galaxy S6 Battery Replacement

Step By Step Guide to Galaxy S6 Battery Replacement

Let’s delve right away into the steps required for Galaxy S6 Battery Replacement. However, before we do that, let’s take a look at the tools that will be required.

Step 1: Eject The Sim Card

Galaxy S6 Battery Replacement 2021 Step by Step Guide

The first thing you must do is Insert a paper clip or SIM eject tool into the hole in the SIM card slot on the power button side of the phone. Press to eject the SIM card tray.

Insert a paper clip or SIM eject tool into the hole in the SIM card slot on the power button side of the phone. Press to eject the SIM card tray.

Note!!! Don’t press too hard or you may damage the SIM card tray.

Remove the SIM card tray from the phone and also Remove the SIM card tray from the phone.

STEP 2: iOpener Heating

We recommend that you clean your microwave before proceeding, as any nasty gunk on the bottom may end up stuck to the iOpener.

Place the iOpener in the center of the microwave.

IMPORTANT!!!

For carousel microwaves: Make sure the plate spins freely. If your iOpener gets stuck, it may overheat and burn.

STEP  3: Heat the iOpener for thirty seconds

Throughout the repair procedure, as the iOpener cools, reheat it in the microwave for an additional thirty seconds at a time.

Be careful not to overheat the iOpener during the repair. Overheating may cause the iOpener to burst!!!

Never touch the iOpener if it appears swollen.

If the iOpener is still too hot in the middle to touch, continue using it while waiting for it to cool down some more before reheating. A properly heated iOpener should stay warm for up to 10 minutes.

RECOMMENDED!!!

STEP 4:

  • Remove the iOpener from the microwave, holding it by one of the two flat ends to avoid the hot center.
  • The iOpener will be very hot, so be careful when handling it. Use an oven mitt if necessary.

STEP 5: Rear Glass Replacement

Opening your phone will compromise its waterproof seals. Have replacement adhesive ready before you proceed, or take care to avoid liquid exposure if you reassemble your phone without replacing the adhesive.

galaxy s6 battery replacement

Take note of these important facts.

  • If your glass is shattered, put packing tape over the entire panel to hold it together during the removal process.
  • Lay the heated iOpener over the rear panel for about two minutes to loosen the adhesive around the edge of the glass.
  • You may need to reheat and reapply the iOpener several times to get the phone warm enough. Follow the iOpener instructions to avoid overheating.
  • Shift the iOpener to heat the remaining section of the panel for another two minutes.

CAUTION!!!

A hairdryer, heat gun, or hot plate may also be used, but be careful not to overheat the phone—the OLED display and internal battery are both susceptible to heat damage.

STEP 6:

Once the rear glass is hot to the touch, apply a suction cup near the bottom edge of the glass.

  • Lift on the suction cup to create a small gap underneath the rear glass, and insert an opening pick into the gap.
  • Optionally, once the pick is inserted, you can add a few drops of isopropyl alcohol into the gap to help weaken the adhesive in the following steps.

STEP 7:

Slide the pick along the bottom edge of the phone to slice through the adhesive securing the rear glass.

Afterward, it may help to leave the pick in place and grab a second pick as you proceed to the next step. Leaving the pick inserted can help prevent the glue you just separated from re-adhering.

Re-heat the rear glass as needed to prevent the glue from cooling and hardening.

STEP 8:

  • Repeat the heating and cutting procedure for the remaining three sides of the phone.
  • Leave an opening pick under each edge to prevent the adhesive from resealing.

-STEP 9:

  • Use an opening pick to slice through any remaining adhesive.
  • Remove the rear glass.

STEP 10:

TO INSTALL NEW REAR GLASS GO THROUGH THE FOLLOWING:

  • Use tweezers to peel away any remaining adhesive from the phone’s chassis.
  • Clean the adhesion areas with high concentration isopropyl alcohol (at least 90%) and a lint-free cloth. Swipe in one direction only, not back and forth. This will help prep the surface for the new adhesive.
  • Peel the adhesive backing off of the new rear glass, carefully line up one edge of the glass against the phone chassis and firmly press the glass onto the phone.
  • If you’re reinstalling the old rear glass or using rear glass without adhesive pre-installed, follow this guide.

STEP 11:

  • Firmly grasp the edge of the midframe assembly.
  • Lift up on the midframe assembly while pushing down on the battery to separate the midframe assembly from the rest of the phone.

Galaxy S6 Battery Replacement

 

  • While lifting the midframe, be careful to avoid snagging it on the audio jack or charging port.
  • Once the midframe is partially separated, carefully run an opening pick around the edges of the rest of the phone to separate the top of the midframe.

Be careful not to accidentally insert the opening pick between the glass and display.

  • To avoid damage to the headphone jack, remove the top of the midframe first, then push the midframe downwards to disengage it from the headphone jack.
  • You may need to heat and apply an iOpener to the edges of the display to soften the display adhesive if midframe separation is difficult.

STEP 12:

Lift the midframe assembly up to separate it from the rest of the phone.

Step 13: Disassembling Samsung Galaxy S6 Battery Connector

Use the flat end of the spudger to disconnect the battery connector from its socket on the motherboard.

Step 14: Dealing with the Battery

  • Insert a plastic opening pick between the case and the battery.

  • Be careful to keep the pick as flat as possible to avoid bending the battery, which may damage it and cause it to release dangerous chemicals.
  • Push the pick further in to separate the battery from the phone.
  • If the battery too strongly adheres for the opening pick, place a warm iOpener over the battery to loosen the adhesive.
  • Alternatively, apply some isopropyl alcohol under each corner of the battery and allow it to penetrate for several minutes to help weaken the adhesive.

CAUTION!!!

Do not pry against the motherboard or you may damage the phone.

STEP 15:

  • Remove the battery from the phone.
  • Do not reuse the battery after it has been removed, as doing so is a potential safety hazard. Replace it with a new battery.

Follow these instructions to install a new battery and adhesive!

If you want to reassemble your Galaxy S6, follow these guides in reverse order. When reinstalling the rear glass, refer to the rear glass adhesive replacement guide, and do so for all others

After completing this guide, calibrate your newly installed battery.

Feel free to share these guides if you found them useful! And also don’t forget to check here for more amazing articles.

Leave a Reply

Your email address will not be published. Required fields are marked *

You May Also Like